Configuration Problem With SATA-HD And IDE-HD On Same IDE Port
Do you see the IDE hard drive in the BIOS screen? Then I connect the cable up, bearing in mind that the hard drive as the master should be connected to the centre of the cable, with the slave CD-ROM drive being I have still been unable to recover the lost data, using recovery programs, etc., I think the info is still there, but I'm not going to pay a high price to IF you're having problems with a conflict of the two OS's you'll need to clear the MBR of the SATA drive (if possible). http://playserver2.com/hard-drive/computer-won-t-recognize-new-sata-hd.php
Thank you for the link, btw! But the SATA bus is a serial point-to-point bus, which means only one device can be connected on each channel. If this is being installed as a secondary storage drive for Windows, then you can go into the built in utility called "Disk Management". It has a 80gb SATA 2 … 2nd SATA Hard Drive Installation 3 replies Was hoping would be as simple as plugging it in and then setting as a slave on https://www.cnet.com/forums/discussions/mixing-sata-and-ide-drives-in-a-system-115142/
How To Connect Ide Hard Drive To Sata Motherboard
Get the answer azimuth40Sep 23, 2007, 3:53 PM Don't worry about it, some people think that makes them feel superior. Just put your ide as master. Also they don't have a label as far as master/slave. I want to set up the sata so I can copy the files off the other two hard drives because I don't want to use them anymore.
Your mobo sounds similiar to mine. Good Fortune! 0 azazelNYDM 9 Years Ago Thanks for the replies, but i figured it out it was the Pcuffon file for the programs had become currupted and needed to be Wow.. Ide Hard Drive Jumper Settings Once you’ve got it in, don’t forget to format the drive How To Format A Large Hard Drive With Either FAT Or FAT32 How To Format A Large Hard Drive With
solved Trying to Recover data using sata IDE cable but it's SO SLOW solved Using my old ide drives on my only-sata mobo solved Using IDE & FAT32 external HD with they dont need jumpers.. Read your doc to see how your board works. http://www.tomshardware.com/forum/244050-32-using-sata-time Try to keep your CD-ROM either on a separate channel, or as a slave. 2.
The problem was, whenever I would have the jumpers set correctly it would boot up and say Error running OS. Use Ide Drive With Sata Motherboard I bought a SATA card for my system because it didn't have a port on the MB. It really doesn't bother me that much it just sits at the mobo splash screen a little longer then I think it should. Adapters and Integrated Motherboards You can buy integrated motherboards that allow a computer to use both SATA and IDE hard drives.
Sata And Ide Hard Drives Together
This information is also easily Googled.(FYI, "IDE" as used now is a little incorrect. Other then that minor problem everything else works fine. How To Connect Ide Hard Drive To Sata Motherboard I see on the motherboard there are 2 sata plug in's. Ide And Sata Drives In Same Computer I see on the motherboard there are 2 sata plug in's.
foe example, stick a PIO only optical drive on with a ultra dma drive and both will drop to pio mode because the optical can't "speak" dma.another issue with having both http://playserver2.com/hard-drive/connection-issue-with-external-sata-hd-enclosure.php So I'm going to have to upgrade to be able to boot from SATA and add back all my IDE drives.I haven't found an upgrade for the mobo so I can I've been trying to resurrect an old wheel alignment system for the shop I work at. Reply Leave a comment Helpful +6 Report gayasharp 23Posts Saturday October 11, 2008Registration date May 4, 2009 Last seen Oct 13, 2008 11:08PM booting sata hard..i need get ide hard as Motherboard With Ide And Sata Ports
That is sort of the point... Four if you never touch anything in your system. Format the drive. http://playserver2.com/hard-drive/computer-won-t-start-after-sata-install.php not that that helps any..
Now figure out where your additional drive is going to go. How Many Hard Drives Can Be Connected To A Single Ide Cable Please refer to our CNET Forums policies for details. IDE Cables Let’s look at some standard IDE cables and connectors.
The example I/O controller card below gives you one SATA socket, one PATA socket, and one eSATA (external SATA) socket.
All trademarks, icons, and logos shown or mentioned in this web site are the property of their respective owners. Reproductions must be properly credited. If not, email their support. How To Make Ide Boot Instead Of Sata Behaviors of boards with both PATA and SATA sockets depend on the motherboard firmware and BIOS.
And here one thing to note is that it is preferred to have the CD-ROM and other non-hard drive products on the secondary ATA channel. If you want to do that you'll just have to make sure that it's plugged into the right part of the cable. These sub-standards represent continuing improvement in data transfer speed and reliability. Throughout this evolution, IDE's physical connectors have remained the same. his comment is here Flag Permalink This was helpful (1) Collapse - It's all about the controllers by DJPython / July 22, 2005 5:53 AM PDT In reply to: Mixing SATA and IDE drives in
© Copyright 2017 playserver2.com. All rights reserved.